Briggs & Stratton 461700 Especificaciones descargar pdf (Pagina 6)

In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information.

Maintenance

See Maintenance Schedule, page 8. Follow the hourly or calendar intervals, whichever occur first.

Note that more frequent service is required when operating in adverse conditions.

WIRE

To prevent accidental starting, remove

spark plug wires from spark plugs and

disconnect battery at negative termi-

nal, if equipped with electric starter,

when servicing engine or equipment.

Oil

Check oil level regularly.

Be sure correct oil level is maintained. Check every 5 hours or

daily, before starting engine. See check oil level on page 3.

Change oil. (Follow Maintenance Schedule.)

Change oil after first 5 hours of operation. Remove drain plug

and drain oil while engine is warm. Replace drain plug. Remove

dipstick and refill with new oil of recommended grade (see chart,

page 3). Start and run engine at idle for 30 seconds. Stop

engine. Wait 30 seconds and re-check oil level. If required, add

oil to bring level to FULL mark on dipstick.

Note: If engine is not

equipped with oil filter, change oil every

25 hours. If engine is

equipped with oil filter, change oil every

50 hours. Change oil more often if engine is operated under

heavy load or high ambient temperatures.

Change oil filter, if equipped. (Follow

Maintenance Schedule.)

Replace oil filter after every 100 hours of operation. Remove

used oil filter. Before installing new filter, lightly oil filter gasket

with fresh, clean oil. Screw filter on by hand until gasket

contacts oil filter adapter. Tighten 1/2 to 3/4 turn more. Start

and run engine at idle to check for leaks. Stop engine.

Re-check oil level. Add oil if required.

Oil filter

Oil drain

OIL DRAIN PLUG

OIL

FILTER

P/N SEE PAGE 8

1/2-3/4 TURN MORE

Oil Pressure

Normal warm operating oil pressure for a pressure lube

engine (engine with oil filter) is 10 to 50 psi at normal operat-

ing temperature. If pressure drops below normal range, stop

engine and check oil level with dipstick. If oil level is between

ADD and FULL mark on dipstick, Do not restart engine

. Contact

an Authorized Briggs & Stratton Service Dealer. Do not operate

engine until oil pressure is corrected.

If oil level is below ADD mark on dipstick, add oil to bring level

to FULL mark. Restart engine and check oil pressure. If

pressure is normal, continue to operate engine.

Note: Oil pressure gauge, if engine is equipped, is supplied

by manufacturer of equipment.

Air cleaner

Dual element air cleaner

KNOBS

COVER

WING NUTS

CARTRIDGE

PLATE

CARTRIDGE

PART NO. 394019

PRE-CLEANER

PART NO. 272490

CARBURETOR

SHIELD

BODY

PRE-CLEANER and CARTRIDGE

PART N0. 5052

Note: Depending on engine Type Number, this engine may

not be equipped with a pre-cleaner.

1. Remove knobs and cover.

2. Carefully slide pre-cleaner off cartridge.

To service pre-cleaner, wash in liquid detergent and water.

Squeeze dry in a clean cloth. Saturate in engine oil. Squeeze

in clean, absorbent cloth to remove all EXCESS oil. Replace if

very dirty or damaged.

3. Remove wing nuts and cartridge plate. Carefully remove

cartridge to prevent debris from entering carburetor.

To service cartridge, clean by tapping gently on a flat surface.

Do not oil cartridge. Replace if very dirty or damaged.

Note: Do not use petroleum solvents, e.g., kerosene, which will

cause the cartridge to deteriorate. Do not use pressurized air

clean cartridge. Pressurized air can damage the cartridge.

4. Reinstall cartridge and cartridge plate. Tighten wing nuts

securely.

5. Reassemble pre-cleaner on cartridge.

6. Replace cover and tighten knobs securely.

Keep muffler area clean and muffler in working order.

Daily or more often, before running engine, clean

muffler area to remove all grass and combustible debris.

If engine muffler(s) is/are equipped with spark arrester

screen(s), remove for cleaning and inspection. Replace if

damaged or plugged.

Muffler area/Spark arrester screens

CLEAN

ARRESTER

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Briggs & Stratton 461700 Especificaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Motor Briggs & Stratton 461700