Briggs & Stratton T22B & T22H Manual del operador descargar pdf (Pagina 10)

STEP 1: Remove the top board from the crate.

Leave the side board facing the tank and wheels

in place. Remove the two end boards and the front

board.

CAUTION: FLATTEN EXPOSED NAILS

WITH A HAMMER TO AVOID

POSSIBLE INJURY.

STEP 2: Remove the tongue assembly (3)* from

the crate. Put the ground stand (34)* in the up-

right position and lock in place with pin (37)*.

STEP 3: Set one of the wood blocks from the

crate underneath the tank (2)* so that it sits in the

upright position.

STEP 4: Attach the tongue (3)* to the tank/axle

assembly (2)* as shown in the diagram using the

two

" NC x 4

" hex cap screws (27)*, lockwash-

ers (28)* and

" NC hex nuts (30)* provided in

the hardware kit. Flatwashers are included in the

hardware kit should it be necessary to use them

as spacers to eliminate play between the tongue

and tank/tongue mounting plate. Tighten. The side

board on the crate keeps the unit stable. Remove

the board after this assembly step is complete.

STEP 5: Roll the tank/tongue assembly (2 & 3)*

off the bottom board of the crate.

STEP 6: Remove the stripper plate (71)* from

the beam (1)* and set it aside. Turn the beam as-

sembly (1)* 90º and center it on the bottom of the

crate. Then slide the cylinder (4)* back as far as

possible from the beam foot plate until it locks.

STEP 7: Attach the stripper plate (71)* to the

3 ASSEMBLY INSTRUCTIONS

NOTE:

The following instructions pertain to Gearmore Log Splitters, models T22B & T22H.

This Log Splitter comes partially assembled. Refer to the drawing and parts list should it become neces-

sary to disassemble the unit for repair or replacement of parts.

beam. You may need to wiggle the plate back and

forth until the holes line up. Use the

" bolts and

" lockwashers provided in the hardware kit.

Place the

" ﬂ atwashers provided in the hardware

kit in front of the lockwashers next to the hole.

Push the stripper plate (71)* down until there is

no play in the bolts. Tighten.

STEP 8: Slide the beam (1)* off the bottom of

the crate and carefully set it upright. Roll the

tank/tongue assembly (2 & 3)* into position be-

tween the two tabs on the beam (1)* as shown in

the diagram. Slide the pivot pin (25)* through the

holes and secure with clip pin (26)*.

STEP 9: Lower the beam (1)* to the horizontal

position so that the hole in the beam ﬁ ts over the

pin (32)* on the tongue (3)*. Lock in place with the

lynch pin (31)* provided in the hardware kit.

STEP 10: Connect the

" I.D. x 35" return hose

(53)* to the

" NPT x

" tube ﬁ tting on the valve

(5)*. Tighten hose clamp (18)*. Remove the plastic

plug from the other valve port and connect the

" I.D. pressure hose coming from the pump (9)*

to the swivel elbow ﬁ tting (50)* on the valve (5)*.

Tighten the nut securely.

STEP 11: Remove the pin and cotter from the

valve (5)* handle. Put the handle in the upright

position and secure with pin and cotter.

* See Parts Breakdown (Pages 15 - 17) in this manual.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Comentarios a estos manuales

Sin comentarios

Briggs & Stratton T22B & T22H Manual del operador Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Cortadoras De Troncos Briggs & Stratton T22B & T22H